Serial Output:

BCM3349A0
100000010346890

MemSize:16M

Flash detected @0xbe000000

Signature:e003

Scientific Atlanta BootLoader Version: V2.1.6r

Build Date: Feb 25 2005

Build Time: 11:07:51

IMG1 Program Header:

Signature:e003

Control:0005

Major Rev:0002

Minor Rev:0000

Build Time:2006/4/4 15:20:08 Z

File Len:1731259 bytes

Load Addr:80010000

Filename:epx2203-p10-5-v202r1152-060404c.bin

HCS:0a99

CRC:b446c0ab

IMG2's HCS fail

Enter '1','2', or 'p' within 2 seconds or take default..
. .

Performing CRC on IMG1..

Decompress LZMA IMG..
Target Addr:0x80010000

...........................

Decompressed length:7078386

Executing IMG1..

eCos - hal_diag_init

Init device '/dev/BrcmTelnetIoDriver'

Init device '/dev/ttydiag'

Init tty channel: 806a0c20

Init device '/dev/tty0'

Init tty channel: 806a0c40

Init device '/dev/haldiag'

HAL/diag SERIAL init

Init device '/dev/ser0'

BCM 33XX SERIAL init - dev: 0.2

Set output buffer - buf: 807bd570 len: 2048

Set input buffer - buf: 807bdd70 len: 2048

BCM 33XX SERIAL config

0x00000014 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Configuring/Loading Flash driver...
0x00000014 [tStartup] FlashDeviceDriver::PlaceRegions: (Flash Driver C API) WARNING - Permanent NonVol would fit in the boot block of this flash device, but I found existing NonVol at the end of Image 1; using this location instead...
0x0000001e [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading ProgramStore driver...
0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading BootloaderStore driver...
0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading NonVol driver...
0x00000032 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Storage drivers initialized successfully.
0x0000003c [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Creating singletons for ProgramStore/BootloaderStore/NonVol devices...
Detecting the next image number that we will store to by default...
0x46 Computing CRC32 over image2 to ensure that it is valid...
ProgramStoreDeviceDriver::ProgramStoreDriverIsImageValid: WARNING - ProgramStore header HCS check failed!
ProgramStoreDeviceDriver::ProgramStoreDriverIsImageValid: WARNING - Header isn't valid!
0x46 Done computing CRC32!
By default, we will dload to image number 2!

By default, we will dload to block number 0!

0x00000050 [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Device abstraction singletons created successfully.

HW BOARD VERSION detected from GPIO[0~4] is 0x1e
Attention:skip_GPIO_manualMode
Function: SetHardcodeVendorProfile

Got Attached ProfileRawData ok

Reading Permanent settings from non-vol...
Checksum for permanent settings: 0x236661a
0x00000064 [tStartup] BcmHalIfNonVolSettings::ReadFromImpl: (HalIf NonVol Settings) WARNING - Read older version of the settings (0.17); they have been upgraded to version 0.18, preserving original settings.
0x00000078 [tStartup] BcmEmtaNonVolSettings::ReadFromImpl: (EMTA Config NonVol Settings) WARNING - Read older version of the settings (0.4); they have been upgraded to version 0.6, preserving original settings.
0x00000082 [tStartup] BcmMiniFirewallNonVolSettings::IsDefault: (Mini Firewall NonVol Settings) Permanent settings are default!
0x00000082 [tStartup] SaMtaNonVolSettings::IsDefault: (SA MTA NonVol Settings) Permanent settings are default!

*
*
* One or more of the settings groups was missing, possibly as a result of a code upgrade.
*
*

*
*
* One or more of the settings groups was upgraded.
*
*
Settings were read and verified.

Reading Dynamic settings from non-vol...
Checksum for dynamic settings: 0x106c08e7
Settings were read and verified.

0x000000a0 [Telnet Thread] BcmTelnetThread::ThreadMain: (Telnet Thread) Telnet server thread running...
Creating SNMP agent cablemodem agent
cablemodem agent disabling management.
cablemodem agent defering traps.
Creating BcmEmtaCommandTable
Creating DOCSIS Control Thread...

vvv Interface creation and driver startup beginning vvv

-> Begin DOCSIS CM WAN interface
Creating HAL object for the DOCSIS CableModem interface
Registering DOCSIS CableModem driver

INTC->RevID = 334900A0, MAX_US_QUEUES = 16, numUsQueuesConfigured = 16
BcmMacInit: advMapRunAheadTimeMin = 2048 (0x00000800) 10.24 MHz ticks, 200 usec
0x000004e2 [tStartup] BcmDocsisCmHalIf::Register: (DOCSIS CableModem HalIf) CM HAL reports h/w support for PHS, bitmask=0x3
0x000004e2 [tStartup] BcmDocsisCmHalIf::Register: (DOCSIS CableModem HalIf) CM HAL reports h/w support for PHS, size=64 bytes.
-> End DOCSIS CM WAN interface

-> Begin Ethernet LAN interfaces
Creating HAL object for the Ethernet interface
Registering Ethernet driver
-> End Ethernet LAN interfaces

-> Begin USB LAN interface
Creating HAL object for the USB interface
Registering USB driver
-> End USB LAN interface

-> Begin IP Stack interfaces
-> Starting V2 DHCP Client subsystem...
Creating HAL object for IP Stack1 (MAC Addr=00:14:f8:e7:21:87)
DHCPc: Created default DHCP lease for IP Stack1
using client id htype=1, value=00:14:f8:e7:21:87; auto-config enabled (IP, subnet, router).
Registering IP Stack1 driver
Tcpip NI: Init - RegisteredStackCount = 1

Creating HAL object for IP Stack2 (MAC Addr=00:14:f8:e7:21:89)
DHCPc: Created default DHCP lease for IP Stack2
using client id htype=1, value=00:14:f8:e7:21:89; auto-config enabled (IP, subnet, router).
Registering IP Stack2 driver
Tcpip NI: Init - RegisteredStackCount = 2

Creating HAL object for IP Stack3 (MAC Addr=00:14:f8:e7:21:8a)
DHCPc: Created default DHCP lease for IP Stack3
using client id htype=1, value=00:14:f8:e7:21:8a; auto-config enabled (IP, subnet, router).
Registering IP Stack3 driver
Tcpip NI: Init - RegisteredStackCount = 3

IP Stack4 not enabled or failed to create and start interface; no other stacks will be loaded.
-> End IP Stack interfaces

^^^ Interface creation and driver startup complete ^^^

Creating the PacketCable Forwarder...
Adding IP Stack2 HalIf to the PacketCable Forwarder
Calling BcmCmDocsisSystem::PostDriverInitialization()...
Creating the DOCSIS Forwarder...
Adding DOCSIS CableModem HalIf as the default interface to the DOCSIS Forwarder
Adding Ethernet HalIf to the DOCSIS Forwarder
Adding USB HalIf to the DOCSIS Forwarder
Adding IP Stack1 HalIf to the DOCSIS Forwarder
Adding IP Stack3 HalIf to the DOCSIS Forwarder

Linking Docsis and PacketCable packet switches...
Adding DOCSIS Embedded Interface HalIf as the default interface to the PacketCable Forwarder
Adding PacketCable Embedded Interface HalIf to the DOCSIS Forwarder
0x0000056e [tStartup] BcmSled::GlobalEnable: (Singleton Instance) WARNING - eDOCSIS SLED is being disabled.
Current IP address is default 0.0.0.0.
0x00000578 [tStartup] BcmEcosIpHalIf::ConfigureLeaseImpl: (IP Stack3 HalIf)
Configuring IP stack 3:
IP Address = 192.168.100.1 (primary IP address)
Subnet Mask = 255.255.255.0
Router = 192.168.100.254
IsPrimaryInterface = 0

Creating Propane Control Thread...
Propane version: 2.0.1 (28 Oct 2002)
Instantiating CmSnmpAgent object.
Starting SNMP subsystem
Registering STP Filter Snoop with all interfaces.
Registering DOCSIS MIB Filter Snoop with CPE and WAN interfaces.
DON'T think we need to go here - so don't:::: init_mib !!!!
WARNING: netsnmp_brcm_create_tstring called with no address!
===> WARNING: Can't add httpMgmtGroup @ 0x80d930ac to iso, group already exists.
0x000008ac [tStartup] BcmDocsisCmHalIf::RegisterSnmpObjects: (DOCSIS CableModem HalIf) Interface 10 additional registration w/ SNMP agent OK.
0x0000091a [tStartup] BcmPacketSwitchBridgingHalIf::RegisterSnmpObjects: (PacketCable Embedded Interface HalIf) Interface 39 additional registration w/ SNMP agent OK.
===> WARNING: Failed to register ScalarMibBridge 1.3.6.1.4.1.4413.2.2.2.1.2.1 to agent Vendor CM Agent w/ BRCM Factory Support
===> Object already bridged.
CmSnmpAgent installing views...
Vendor CM Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted
Vendor CM Agent w/ BRCM Factory Support installing engine ID...
Vendor CM Agent w/ BRCM Factory Support installing context...
Creating SNMP agent CPE diag agent
Vendor CPE Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted
Vendor CPE Agent w/ BRCM Factory Support installing engine ID...
Vendor CPE Agent w/ BRCM Factory Support installing context...
Vendor CPE Agent w/ BRCM Factory Support setting V1/V2 view to docsisCpeView
Vendor CPE Agent w/ BRCM Factory Support ConfigIp: Ip=192.168.100.1, Subnet=255.255.255.0, Gateway=0.0.0.0
Vendor CPE Agent w/ BRCM Factory Support enabling management.
Vendor CPE Agent w/ BRCM Factory Support sending deferred traps...
Done w/ deferred traps.
BcmSnmpThread starting thread operation.
SNMP startup complete.
kConsoleIsReadWrite
fpBridge is Not Null !!!
0x00000cb2 [tStartup] BcmVendorCmApplication::CreateDhcpServer: Configuring the DHCP server with 50 leases from 192.168.100.10 -> 192.168.100.60; lease time is 30 seconds.
0x00000cd0 [tStartup] BcmVendorCmApplication::StartDhcpServer: Starting DHCP Server!
Reseting the 3341BOS: Enter bosInit
BOS: Exit bosInit
Creating SNMP agent EMTA agent
EMTA agent entering RFC-2576 Coexistence security mode.
EMTA agent setting V1/V2 view to coexistenceView
EMTA agent entering Basic/Hybrid flow provisioning mode.
MTA : Register for CM VSIFs
maintMgmtTask: created MAINT task.

EMTA battery callback = 0x803bdc50
0V0x00000de8 [IpsecTimer] IpsecTimer::ThreadMain: Entering...
x00000df2 [aoRT] AppResetRootTask: (cxc-BOS)

bosAppRootTask() - Is it morning already? Spawning app task (epoch #0)...

0x00000dfc [aoRT] bosTaskCreateMain: (cxc-BOS) TaskCreate - spawn new task aoAP
Maendor CM Event Log initializing with stored events.
intMgmtTaskMain: waiting for kickoff sema4 ...

Reseting the 3341
PASS: mmr
PASS: chipCtl
PASS: apmregs
Event log initialization complete.
PASS: apm0
PASS: apm1
0x00000f00 [tStartup] BcmPacketSwitchBridgingHalIf::RegisterSnmpObjects: (DOCSIS Embedded Interface HalIf) Interface 40 additional registration w/ SNMP agent OK.
emta factory agent installing engine ID...
emta factory agent installing context...
emta factory agent setting V1/V2 view to
emta factory agent setting V1/V2 view to docsisNmAccessView
StartUsb()...
0x00000f50 [tStartup] BcmSled::Register: (Singleton Instance) WARNING - PacketCable Embedded Interface is already registered!
Checking board manufacturing state...
Board appears to be manufactured OK.

Running the system...

Beginning Cable Modem operation...

Beginning MTA operation...

X0DRV_SLIC: Program the SLIC for 25mA current limit !!!
XDRV_APM: ERROR - voltage level '0' not supported !!!
XDRV_SLIC: Program the SLIC for 25mA current limit !!!
XDRV_APM: ERROR - voltage level '0' not supported !!!
PASS: mspi
PASS: scratchSram
PASS: vpm
PASS: mbox
Reseting the 3341
x00001284 [Scan Downstream Thread] BcmVendorCmDownstreamScanThread::ThreadMain: (Scan Downstream Thread) Scanning for a Downstream Channel...
Scanning DS Channel at Vendor NonVolSetting : 331000000 Hz...
XDRV_SLIC: Program the SLIC for 25mA current limit !!!
XDRV_SLIC: Program the SLIC for 25mA current limit !!!
Loading 3341 Zsp with Hausware app.
0x000012de [aoAP] bosTaskCreateMain: (cxc-BOS) TaskCreate - spawn new task 3341_ASSERT_IST
DSP Handshake. Hausware ZSP app initialized properly.
0x000012f2 [aoAP] bosTaskCreateMain: (cxc-BOS) TaskCreate - spawn new task HTSK
boardHalInit3348: Initialization complete.
RingClipModes (Get)
-------------
0x55200000

RingFreqAmp (Get)
-------------
0x06D47FFF

RingFreqAmp (Set)
-------------
0x06D47FFF

RingClipModes (Set)
-------------
0x55200000

RingClipModes (Get)
-------------
0x55200000

RingScaleOffset (Set)
-------------
0x39D80000

RingClipModes (Set)
-------------
0x55200000

boardHalInit completed

CC: Initialization starting...

Scanning DS Channel at Power-Up List: 130750000 Hz...
MaintMgmtTaskMain: up and running.

Type 'help' or '?' for a list of commands...

CM> Scanning DS Channel at Power-Up List: 236000000 Hz...
Scanning DS Channel at Power-Up List: 514750000 Hz...
Scanning DS Channel at Power-Up List: 122500000 Hz...
Scanning DS Channel at Power-Up List: 162000000 Hz...
Scanning DS Channel at Power-Up List: 307750000 Hz...
Scanning DS Channel at Power-Up List: 313750000 Hz...
Scanning DS Channel at Power-Up List: 319750000 Hz...
Scanning DS Channel at Power-Up List: 325750000 Hz...
Scanning DS Channel at Power-Up List: 465000000 Hz...
Scanning DS Channel at Power-Up List: 138000000 Hz...
Scanning DS Channel at Power-Up List: 415750000 Hz...
Scanning DS Channel at Power-Up List: 115125000 Hz...
Scanning DS Channel at Power-Up List: 123125000 Hz...
Scanning DS Channel at Power-Up List: 147125000 Hz...
Scanning DS Channel at Power-Up List: 130000000 Hz...
Scanning DS Channel at Power-Up List: 146000000 Hz...
Scanning DS Channel at Power-Up List: 154000000 Hz...
Scanning DS Channel at Power-Up List: 147125000 Hz...
Scanning DS Channel at Power-Up List: 155125000 Hz...
Scanning DS Channel at Power-Up List: 163125000 Hz...
Scanning DS Channel at Power-Up List: 171125000 Hz...
Scanning DS Channel at Power-Up List: 234000000 Hz...
Scanning DS Channel at Power-Up List: 266000000 Hz...
Scanning DS Channel at Power-Up List: 570375000 Hz...
Scanning DS Channel at Power-Up List: 602375000 Hz...